Plumbers' Testing Equipment

PLUMBERS' WET & DRY TEST KIT

HAYES H2&O professional plumbers' wet and dry kit is based around the most commonly used pressure test equipment, contained in a durable carrying case.
Qty Description
1
Dry test gauge 63 mm diameter, 0 - 4 bar x 15 mm JG Speedfit complete with Schrader valve test point for use with Peak Reading Needle
1
63 mm diameter pressure gauge 0 - 11 bar for use with Peak Reading Needle
1
63 mm diameter pressure gauge 0 - 25 bar for use with Peak Reading Needle
3
rubber gauge boots fitted to the above
1
rubber tap connector
1
10 bar flexible hose
1
gauge adaptor
1
PVC covered chain complete with 2 screws and washer
1
chrome plated reducing bush 3/4" x 1/2"
1
JG Speedfit 15 mm x 1/2" stud
1
JG Speedfit 15 mm x 1/2" stem
1
JG Speedfit 22 mm x 3/4" stud
1
JG Speedfit 22 mm x 3/4" stem
6
O rings
1
filling tee adaptor 1/4"
1
plastic carrying case
Part No.Description Unit PriceQty



WATER PRESSURE GAUGES

Water Pressure Gauges

May be used for checking mains pressure, for example when considering the fitment of a combination boiler.
Push-on connectors to fit most 1/2" or 3/4" taps. Supplied with a safety chain. With 2" diameter gauge.
Part No.Description Unit PriceQty

Water and Air Pressure Gauges

Pressure gauges with ABS plastic body and perspex faces, for use with air or water. Body diameters as below (in mm). Threads BSP parallel male, sizes as below.
Part No.Description Unit PriceQty



DRY PRESSURE TEST GAUGE

Suitable for pressure-testing water, air, gas and oil pipes up to 60 p.s.i.. Ideal for dry-testing combi systems. Especially useful when testing push-fit pipes and fittings, also for testing underfloor heating pipework for damaged piping. Supplied fitted with a 15mm push-fit connection. 0 - 4 bar and 0 - 60 p.s.i. scales.
Part No.Description Unit PriceQty



PRESSURE & FLOW KIT

The kit comprises three separate pieces of equipment.

0 - 10 bar water pressure gauge with 54 mm dial, brass fittings and rubber tap connector to fit most taps (supplied with safety chain). ABS flow measure with dual scale, 2.5 to 22 litres and 1/2" to 5 gallons per minute.
Dry pipe test gauge with 0 to 4 bar dial fitted with drag pointer.

Uses 15 mm Speedfit connector. Fitted with Schraeder valve for pressurisation. All suitably fitted in a sturdy carrying case.
Part No.Description Unit PriceQty



TEMPERATURE GAUGES

Stainless Steel body and perspex faces, for use with air or water. Body diameters as shown below (in mm). 1/2" BSP parallel male thread. Temperature sensing pocket (12 mm outside dia.) protrudes 35 mm beyond the thread.
Please click here for digital thermometers.
Part No.Description Unit PriceQty

Part No.Description Unit PriceQty



WEIR GAUGES (FLOW METERS)

Used for measuring water flow rates. Useful when setting up combination boilers to help adjust the flow to the correct rate per minute.
When water flows through the gauge, the flow rate is measured off the calibrated slot.
Calibrated 0.5 to 5 gallons and 2.5 to 22 litres per minute.
Tough ABS plastic vessel.
Part No.Description Unit PriceQty



HYDRAULIC TEST PUMP

HILMOR light, portable and compact 50 bar test pump for leak testing in water pipe systems (a test is recommended for all pressurised plastic pipe plumbing and central heating applications). The test is carried out with the system full of water.
Not suitable for gas pipe testing because water must be used.
Robust powder-coated steel construction, with easy-fill reservoir and in-built carrying handle.
Part No.Description Unit PriceQty



PUMP HEAD ADAPTOR

The FERNOX powerflow pump head adaptor allows easy connection of power flushing machines to central heating systems via the body of the circulator pump. Also allows for cleaning of secondary heat exchangers without dismantling the boiler. Useful for combination/ condensing boilers with in-built circulators.
Part No.Description Unit PriceQty