Electrical Test & Soldering Equipment

FUSE & SOCKET TESTERS

Fuse Finder Kits

MARTINDALE FD 500 standard fuse finding kit is easy to use and allows you to track circuits from socket to socket or from socket to fuse. The transmitter takes its power from the mains and emits a signal which the adjustable sensitivity receiver can pick up. This combination can easily distinguish the appropriate circuit, even when used on adjacent fuses.
Part No.DescriptionUnit PriceQty

MARTINDALE FD 600 professional fuse finding kit has an IEC socket with a standard UK 3 pin mains adaptor. This allows the user to trace from sockets and, with the included TL83 lead, traces can be made at light fittings or other points in a circuit where there is no power socket.

This kit comes complete with carrying case, TL83 lead, transmitter and receiver.
Part No.DescriptionUnit PriceQty


CIRCUIT TEST METER

Checks if domestic AC circuits are live. Tests for circuit continuity with power off. Measures battery voltage and tests DC circuits. Manufactured to BS 5458. Battery not included. One PP3 disposable battery is required, P/N 7596. For batteries please click the following link: Batteries
Part No.DescriptionUnit PriceQty


SOLDERING IRONS

Manufactured to BS EN 60335-2-45: 2002 specification. Supplied complete with tip, BS approved 3 pin plug and 1.2 m (approx) of cable.
Part No.DescriptionUnit PriceQty


PIPE-MASTER PROFESSIONAL

Suitable for end feed, capillary or solder ring fittings. Ideal for confined spaces and where a flame may be hazardous.

SPECIFICATION :
Voltage : 230 V AC
Power : 220 W. Temperature controlled
Head Temperature : 520°C
Warm up time : 2 minutes approx.
Cable lead : 1.4 m / 55"
Standard head : 15 mm
Part No.DescriptionUnit PriceQty


MARTINDALE PLUG-IN SOCKET TESTERS

Classic

MARTINDALE classic check plug socket tester is ideal for rapid socket testing. Plugged into a live 13 A socket it will identify almost all faults. Fault indications are instantly identified using the key on the face label. Three long life high intensity neons all indicate when the circuit is correctly wired. This fail safe system means any neon not lighting shows a problem. The check plug induces less than 5 mA of earth leakage, well below RCD trip thresholds. Designed for easy insertion and removal, the case is made from flame retardant ABS.
Part No.DescriptionUnit PriceQty

Non-trip Earth Loop Impedance Checker

MARTINDALE E-Ze check Xtra socket tester has been designed to check not only if the earth is connected, but also to tell you how good it is. Along with the facility to check the voltage and socket.

SPECIFICATIONS :
Normal operating voltage : 230 V
Frequency : 50 Hz
Non-trip earth loop impedance ranges : 0 - 1.7 - 5 - 10 - 100 - 200 - 500 ohms
Earth loop threshold accuracy : ± (10 % + 0.3 ohms)
Voltage low indication : <195 V
Voltage high indication : >270 V
Open earth indication : >500 ohms
Power consumption : < 1.6 W
Overvoltage category : Cat 11/300 V
Dimensions : approx. 65 mm x 65 mm x 50 mm
Weight : 64 g
Part No.DescriptionUnit PriceQty

‘Buzz-It’ Check Plug with Audible Alarm

A fast and easy way to ensure 13 A sockets are wired correctly. Plugged into a live 13 A socket it will identify almost all faults. Fault indications are instantly identified using the key on the face label. Three long life high intensity LEDs all indicate when the circuit is correctly wired and the ‘Buzz-It’ gives an audible signal to allow any awkwardly placed, or not easily visible sockets to be checked. This fail safe system means any LED not lighting or making an audible signal shows a problem. The check plug induces less than 5 mA of earth leakage, well below RCD trip thresholds. Designed for easy insertion and removal, the case is made from flame retardant ABS. It can also be used as a basic fuse finder, when the correct fuse is pulled the buzzer stops.
Part No.DescriptionUnit PriceQty

’Safebreak’ Socket Test Adaptor

Essential for safe and fast testing without removing the wall socket faceplate. Enables good connection to the wiring installation using standard 4 mm test probes. Speeds up R2, R1+R2 measurements, periodic, 17th Edition and Part P testing. Suitable for use with any meter with industry standard 4 mm plugs.
Part No.DescriptionUnit PriceQty


ELECTRICAL SOCKET TESTER

The socket tester will show where the fault is - live, earth or neutral. A total of 17 wiring fault conditions can be indicated. A continuous or warbling tone gives an indication of good or faulty wiring, built-in self-check at start of test ensures correct operation at all times.
Part No.DescriptionUnit PriceQty


WIRE, PIPE, POWER DETECTOR

Electronically locates cables, gas and water pipes, electric conduits and steel joists. Detects mains power and traces breaks in circuits and cables. Will detect at the following depths:

Conduit : 3" - 3.1/2".
Cable : 1" - 1.1/2".
Copper pipe : 1" - 1.1/4".
Reinforcing bar : 2.3/4" - 3 ".
Screw : 1 - 1.1/4".

NOT SUITABLE FOR USE ON CONCRETE
Battery not included. One PP3 disposable battery is required, P/N 7596. For batteries please click the following link: Batteries
Part No.DescriptionUnit PriceQty


MARTINDALE MINI CLAMP METER

The MARTINDALE CM51 is a low cost 200 A electrical mini clamp meter
with autoranging, display hold and auto power down. The two ranges
mean that when measuring 40 A and lower currents the resolution
increases from 100 mA to 10 mA. Autoranging ensures that the most
suitable range is always automatically selected. Complete with battery
and carrying case.

SPECIFICATIONS :
3.1⁄2" digit LCD display with annunciators. Display hold DH button.Display update 25 times per second. AC A ; 10 mA to 200 A, autoranging (2 ranges)(40 Hz to 500 Hz).
Max. conductor size : 27 mm dia.
Dimensions : length 150 mm x width 52 mm x depth 24 mm
Operating temp. : 0 °C to 40 °C at < 80% RH
Weight : 110 g
Auto power off : after 10 minutes
Overvoltage : Category III, 300 V
Low battery warning : “BAT” symbol
Overrange indication : “OL” symbol

Part No.DescriptionUnit PriceQty